Reasons Your fiat 500 flip key repair 500 Key Fob Won't Work

A fiat punto key replacement cost 500 key fob allows you to easily open doors and start your vehicle. However, there are numerous reasons the fob could stop working. This could be due to a dead coin-battery water damage, problems with receiver modules, as well as interference.

This listing is for an NEW replacement Fiat Flip Key Remote - like the Ilco brand that needs to be programmed professionally by a local automotive locksmith (click here for Locksmith Search). Includes lock, unlock, and trunk buttons.

Dead Coin Battery

A dead battery is probably the most common cause of your 500 key fob that isn't working. Modern key fobs have a restricted operating range, and should be within some feet of the vehicle to function. If you are far from your car and hit the keyfob, it will not respond and display the message "Key Fob Not Detected".

If this happens, replace the battery in the coin cell (Part number CR2032) by a new one from a trusted brand such as Panasonic, Duracell, or Energizer. You can typically find them at your local hardware store or online.

You can test the battery in the coin-cell by pressing the buttons while you are standing close to your fiat key replacement near me 500. The car should blink its parking lights and the key fob should work the lock and unlock switches.

If the key fob won't work after replacing the battery, it could be damaged by water, which prevents it from communicating with the receiver module inside your vehicle. Water damage can occur in a variety of ways, ranging from an accidental splash to submerging the fob into salt water at the beach. If you suspect that your fob was exposed to water, try placing it in a dry rice bag to draw the moisture back out. If this doesn't work, the fob might need to be reprogrammed by an experienced auto locksmith or dealer.

Water Damage

Water damage can occur if you submerge the fob in the ocean or wash it in a washer. Saltwater can cause the circuit board to become shorted and eventually end up dying. If you get the fob wet, it's not an option but if you drop it into a cup of water or fail to remove it from your pants pocket prior to running the washing machine Don't give up hope.

First, remove the battery from the fob. Before replacing the battery clean the electronic chip using isopropyl or similar products. Then, test the fob to verify if it is working. If the key doesn't work, it might need to be reprogrammed. This is typically done by a dealer or professional auto locksmith.

If your key is older and has not been programmed to work with your vehicle then you'll need to replace it completely. This is a simple procedure that can be completed by a professional automotive locksmith. The locksmith will require the key cut to match your vehicle's ignition. The locksmith will also have to reprogram the fob into the car's system. This is an affordable and fast process that can be completed within the same day.

Receiver Module Issues

One of the main reasons your 500 key fob won't be working is because it's out of range. The remote has a maximum range of 30 feet. Therefore, should you be too far from your vehicle, it won't respond to your commands. This can be easily fixed by moving closer to your vehicle until it begins responding.

If you've replaced the battery on your coin (commonly known as"button" or "button" or "watch") and your fob still won't work It could be because of an internal circuit board issue. In the majority of cases, reprogramming your fob can resolve the problem. You can find the instructions for most vehicles on YouTube or in the owner's manual.

It's possible that you need to replace the metal clips that hold the coin battery in place. If they loose tension, they could stop the battery from being seated properly and result in the malfunction of your remote.

In rare instances, the fob could be out of connection with your vehicle as a result of software or hardware problems. You can fix this problem by visiting your local dealer or auto-locksmith to reprogram your key fob. In certain instances they might need to reinstall the program in your body control module, too.

Interference

In addition to a dead battery on a coin The key fob might not be able to transmit or receive a signal due to interference. This could happen when the keyfob's location is in close proximity to a radio transmitter, such as a cell phone or radar detector. Other reasons why the key fob might not work include a weak connection to the buttons, damage to the internal chip, or water damage.

If your key fob suddenly stopped working, or you have tried everything at home to solve the issue (e.g. battery replacement, reprogramming and using the spare key fob, you could have a faulty receiver module on your 500. The receiver module is situated under the dash, and it picks up the radio frequency signals from the key fob. It transforms the signals into electronic commands that are then processed by the vehicle.

There is a simple way to reset the 500's onboard system, including the keyfob. Disconnect the 12 volt battery for about 15 minutes, by removing the negative cable and then the positive cable. Reconnect the battery. This will remove any residual electricity and restart the car's computer system, which can help you the key fob to function again. If the issue continues it is recommended that you consult an expert certified technician. They will be able to identify the exact cause of any issues.